admin:printer_installation

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
admin:printer_installation [2020/07/21 08:23] – [Zebra TLP 2844] Ujwal Khatryadmin:printer_installation [2024/03/05 00:08] (current) – [25.18. Label printer hardware setup] Nick Pendergrast
Line 1: Line 1:
 {{indexmenu_n>195}} {{indexmenu_n>195}}
-====== 23.18. Label printer hardware setup ====== +====== 25.18. Label printer hardware setup ====== 
- +We recommend **Zebra ZD421t** (which has replaced the Zebra GK420t which we recommended previously) label printer with a network port.\\
-We recommend **Zebra GK420t** label printer with a network port.\\+
 You may use other printers that support the ZPL printing language (or EPL if using mSupply 3.2 or earlier), but we cannot provide much support for these models as we have not used them ourselves. You may use other printers that support the ZPL printing language (or EPL if using mSupply 3.2 or earlier), but we cannot provide much support for these models as we have not used them ourselves.
  
Line 13: Line 12:
   - There are now 2 options for setting a static address   - There are now 2 options for setting a static address
     - (Preferred method): Configure your DHCP server to assign a static address to the printer. Note that after doing this, you may have to turn the printer off and back on to get the new address from the DHCP server.     - (Preferred method): Configure your DHCP server to assign a static address to the printer. Note that after doing this, you may have to turn the printer off and back on to get the new address from the DHCP server.
-    - Alternative: Assign a static address on the printer itself. The default static address for the printer is 192.168.254.254. +    - Alternative: Assign a static address to the printer.  
-      - You can now log on to the printer using it's current IP address http://printer_ip_address  where ''printer_ip_address'' is the current printer's ip address.+      - The default static address for the printer is 192.168.254.254. 
 +      - If you are connecting to that address, you must assign your own computer a 192.168.254.X address so it can connect to the printer. You can then log on to the printer using it's current IP address http://printer_ip_address  where ''printer_ip_address'' is the current printer's ip address (So, out of the box: http://192.168.254.254 )
       - Go to "Print Server Settings", then click "Print Server" and log in       - Go to "Print Server Settings", then click "Print Server" and log in
         * user: admin         * user: admin
Line 26: Line 26:
  
 ==== GK420 Flash sequences ==== ==== GK420 Flash sequences ====
-This is a menu on the printer itself that you access by holding down the Feed button.\\ +This is a feature on the printer itself that you access by holding down the Feed button.  Refer here for full documentation: https://support.zebra.com/cpws/docs/gseries/gseries_button_modes.pdf
-With the printer power on and top cover closed, press and hold the Feed button for several secondsThe green status LED on the printer will flash a number of times in sequence\\ +
-It will flash on and off 1 time\\ +
-...then on and off twice\\ +
-...on and off 3 times\\ +
-...on and off 4 times\\ +
-...on and off 5 times\\ +
-...on and off 6 times\\ +
-...on and off 7 times\\ +
-You can select each of the below menu items by **releasing** the button +
-after the light starts that specific number of flashes and before the next flash sequence starts. +
-  - Print a configuration status label +
-  - Auto Media calibration: use to make the printer detect the length of the labels you're using +
-  - Serial port config: not needed +
-  - Factory defaults: Sets everything back to default settings +
-  - Print width adjustment (above) +
-  - Print Darkness (Density) Adjustment +
-  - Manual media calibration (you most likely don't need this)+
  
 ==== Calibrating the printer GK420 ==== ==== Calibrating the printer GK420 ====
Line 110: Line 93:
 Click to download the user guide for  {{ :admin:zebra_manual-tlp_2844.pdf |Zebra TLP 2844}} Click to download the user guide for  {{ :admin:zebra_manual-tlp_2844.pdf |Zebra TLP 2844}}
  
-On page 48 the manual has a guide on how to Manually calibrate the printer.  +On page 48 the manual has a guide on how to manually calibrate the printer.  
  
 \\ \\
Line 117: Line 100:
  
 ---- struct data ---- ---- struct data ----
 +pagestatus.status    : 
 ---- ----
  
  • Last modified: 2020/07/21 08:23
  • by Ujwal Khatry